Frequency Response

Frequency Response

Frequency Response of an amplifier or filter shows how the gain of the output responds to input signals at different frequencies.

Amplifiers and filters are widely used electronic circuits that have the properties of amplification and filtration, hence their names.

Amplifiers produce gain while filters alter the amplitude and/or phase characteristics of an electrical signal with respect to its frequency. As these amplifiers and filters use resistors, inductors, or capacitor networks (RLC) within their design, there is an important relationship between the use of these reactive components and the circuits frequency response characteristics.

When dealing with AC circuits it is assumed that they operate at a fixed frequency, for example either 50 Hz or 60 Hz. But the response of a linear AC circuit can also be examined with an AC or sinusoidal input signal of a constant magnitude but with a varying frequency such as those found in amplifier and filter circuits. This then allows such circuits to be studied using frequency response analysis.

Frequency Response of an electric or electronics circuit allows us to see exactly how the output gain (known as the magnitude response) and the phase (known as the phase response) changes at a particular single frequency, or over a whole range of different frequencies from 0Hz, (d.c.) to many thousands of mega-hertz, (MHz) depending upon the design characteristics of the circuit.

Generally, the frequency response analysis of a circuit or system is shown by plotting its gain, that is the size of its output signal to its input signal, Output/Input against a frequency scale over which the circuit or system is expected to operate. Then by knowing the circuits gain, (or loss) at each frequency point helps us to understand how well (or badly) the circuit can distinguish between signals of different frequencies.

The frequency response of a given frequency dependent circuit can be displayed as a graphical sketch of magnitude (gain) against frequency (ƒ). The horizontal frequency axis is usually plotted on a logarithmic scale while the vertical axis representing the voltage output or gain, is usually drawn as a linear scale in decimal divisions. Since a systems gain can be both positive or negative, the y-axis can therefore have both positive and negative values.

In Electronics, the Logarithm, or “log” for short is defined as the power to which the base number must be raised to get that number. Then on a Bode plot, the logarithmic x-axis scale is graduated in log10 divisions, so every decade of frequency (e.g, 0.01, 0.1, 1, 10, 100, 1000, etc.) is equally spaced onto the x-axis. The opposite of the logarithm is the antilogarithm or “antilog”.

Graphical representations of frequency response curves are called Bode Plots and as such Bode plots are generally said to be a semi-logarithmic graphs because one scale (x-axis) is logarithmic and the other (y-axis) is linear (log-lin plot) as shown.

Frequency Response Curve

frequency response curve

Then we can see that the frequency response of any given circuit is the variation in its behaviour with changes in the input signal frequency as it shows the band of frequencies over which the output (and the gain) remains fairly constant. The range of frequencies either big or small between ƒL and ƒH is called the circuits bandwidth. So from this we are able to determine at a glance the voltage gain (in dB) for any sinusoidal input within a given frequency range.

As mentioned above, the Bode diagram is a logarithmic presentation of the frequency response. Most modern audio amplifiers have a flat frequency response as shown above over the whole audio range of frequencies from 20 Hz to 20 kHz. This range of frequencies, for an audio amplifier is called its Bandwidth, (BW) and is primarily determined by the frequency response of the circuit.

Frequency points ƒL and ƒH relate to the lower corner or cut-off frequency and the upper corner or cut-off frequency points respectively were the circuits gain falls off at high and low frequencies. These points on a frequency response curve are known commonly as the -3dB (decibel) points. So the bandwidth is simply given as:

frequency response bandwidth

The decibel, (dB) which is 1/10th of a bel (B), is a common non-linear unit for measuring gain and is defined as 20log10(A) where A is the decimal gain, being plotted on the y-axis. Zero decibels, (0dB) corresponds to a magnitude function of unity giving the maximum output. In other words, 0dB occurs when Vout = Vin as there is no attenuation at this frequency level and is given as:

zero decibels

We see from the Bode plot above that at the two corner or cut-off frequency points, the output drops from 0dB to -3dB and continues to fall at a fixed rate. This fall or reduction in gain is known commonly as the roll-off region of the frequency response curve. In all basic single order amplifier and filter circuits this roll-off rate is defined as 20dB/decade, which is an equivalent to a rate of 6dB/octave. These values are multiplied by the order of the circuit.

These -3dB corner frequency points define the frequency at which the output gain is reduced to 70.71% of its maximum value. Then we can correctly say that the -3dB point is also the frequency at which the systems gain has reduced to 0.707 of its maximum value.

Frequency Response -3dB Point

frequency response -3dB point

The -3dB point is also know as the half-power points since the output power at this corner frequencies will be half that of its maximum 0dB value as shown.

frequency response half power points

Therefore the amount of output power delivered to the load is effectively “halved” at the cut-off frequency and as such the bandwidth (BW) of the frequency response curve can also be defined as the range of frequencies between these two half-power points.

While for voltage gain we use 20log10(Av), and for current gain 20log10(Ai), for power gain we use 10log10(Ap). Note that the multiplying factor of 20 does not mean that it is twice as much as 10 as the decibel is a unit of the power ratio and not a measure of the actual power level. Also gain in dB can be either positive or negative with a positive value indicating gain and a negative value attenuation.

Then we can present the relationship between voltage, current and power gain in the following table.

Decibel Gain Equivalents

Decibel Gain Equivalents

Operational amplifiers can have open-loop voltage gains, ( AVO ) in excess of 1,000,000 or 100dB.

Decibels Example No1

If an electronic system produces a 24mV output voltage when a 12mV signal is applied, calculate the decibel value of the systems output voltage.

frequency response example one

Decibels Example No2

If the output power from an audio amplifier is measured at 10W when the signal frequency is 1kHz, and 1W when the signal frequency is 10kHz. Calculate the dB change in power.

frequency response example two

Frequency Response Summary

In this tutorial we have seen how the range of frequencies over which an electronic circuit operates is determined by its frequency response. The frequency response of a device or a circuit describes its operation over a specified range of signal frequencies by showing how its gain, or the amount of signal it lets through changes with frequency.

Bode plots are graphical representations of the circuits frequency response characteristics and as such can be used in solving design problems. Generally, the circuits gain magnitude and phase functions are shown on separate graphs using logarithmic frequency scale along the x-axis.

Bandwidth is the range of frequencies that a circuit operates at in between its upper and lower cut-off frequency points. These cut-off or corner frequency points indicate the frequencies at which the power associated with the output falls to half its maximum value. These half power points corresponds to a fall in gain of 3dB (0.7071) relative to its maximum dB value.

Most amplifiers and filters have a flat frequency response characteristic in which the bandwidth or passband section of the circuit is flat and constant over a wide range of frequencies. Resonant circuits are designed to pass a range of frequencies and block others. They are constructed using resistors, inductors, and capacitors whose reactances vary with the frequency, their frequency response curves can look like a sharp rise or point as their bandwidth is affected by resonance which depends on the Q of the circuit, as a higher Q provides a narrower bandwidth.

Author: admin

Leave a Reply